Approved installersEWIPROCERESITManufacturer guarantees on qualifying system installations
Silicone rendering · 7 min read

Can silicone render go over existing render or paint?

How a survey determines whether an existing finish can be prepared and retained, or whether removal is the safer starting point.

· Pro Rend Sussex team

If your property already has painted render, pebble dash or an older render finish, you may wonder whether silicone render can simply be applied over it.

Sometimes an existing surface can form part of a suitable new render system. In other cases, the old coating or render needs to be removed. The decision depends on its strength, adhesion, condition and compatibility with the proposed materials.

Covering an unsuitable background can leave the new finish relying on a weak layer underneath. A proper assessment is therefore essential before choosing between an overlay system, local repairs or complete removal.

Why the existing surface matters

A silicone render system is only as dependable as the surface supporting it. An elevation may look reasonably sound from the ground while still containing hollow render, loose paint, concealed cracks or areas affected by moisture. These problems can interfere with adhesion and may eventually cause cracking or sections of the new system to detach.

EWI Pro advises that existing render should be assessed for stability, moisture, contamination and compatibility before another finish is applied. It also warns that new render can inherit unresolved defects in the existing façade.

Ceresit gives similar preparation guidance for its CT 74 silicone finish. The manufacturer requires a sound, dry and clean substrate, with damaged areas repaired and weak layers or unsuitable paint coatings removed.

There is no reliable one-size-fits-all answer. The wall and the proposed system need to be considered together.

What should be checked during a render survey?

Is the old render firmly attached?

The existing render should be checked for hollow, loose or crumbling areas. Visible bulges, open edges and sections that sound hollow when assessed can indicate that the render has lost its bond with the wall.

Small isolated defects may sometimes be removed and repaired. Widespread failure usually makes retaining the existing render a much less dependable option.

Is the wall painted?

Paint can create an unsuitable interface between the existing wall and the new render system. Its condition and type must be established rather than assuming that a primer will solve every problem.

EWI Pro lists a specific render-only build-up for painted brick backgrounds that includes a universal primer and mechanical scrim-and-pin fixing. That is a defined system specification, rather than general permission to apply any render directly over paint. Where paint is peeling, chalky or poorly adhered, keeping it beneath a new system would leave the finished work dependent on that weak coating.

Are there cracks?

Cracks should be investigated before they are covered. The important question is why the crack formed. Possible causes include failed render, movement around an opening or deterioration in the masonry underneath. Applying a decorative finish without addressing the cause can allow the crack to reappear.

Completed Hove property after old pebble dash was removed, brickwork repaired and an EWI Pro Ash silicone render system installed
Hove project: old pebble dash removed, brickwork treated and crack-stitch repairs completed before the silicone render system was installed.

Is moisture present?

Signs such as persistent staining, blistering paint, algae or damp patches need attention before rendering starts. The source might be a leaking gutter, damaged coping, failed seal, defective pipework or another building detail. Covering the symptom does not correct the cause. The wall also needs to be sufficiently dry for the selected materials and primer.

Is the surface clean enough?

Dirt, dust, organic growth and weak surface material can all reduce adhesion. Cleaning is part of preparation, but it does not turn unsound render into a suitable background. Any remaining coating must still be stable and compatible with the complete manufacturer-specified system.

When might an overlay system be suitable?

An overlay may be considered when the existing render is:

  • Firmly bonded across the elevation.
  • Free from unresolved damp or water ingress.
  • Structurally stable and not extensively cracked.
  • Clean and capable of accepting the specified preparation.
  • Compatible with a complete render system approved for that background.

Depending on the substrate and manufacturer’s specification, preparation may include local repairs, cleaning, a suitable primer, a reinforced basecoat and fibreglass mesh before the silicone finish.

The precise build-up should be selected after the wall has been inspected. Products from different systems should not be combined simply because they appear to perform similar jobs.

When is removing the old render the better option?

Removal is more likely to be recommended where:

  • Large areas sound hollow or are separating from the wall.
  • The render is soft, friable or heavily cracked.
  • Several unknown coatings have accumulated.
  • Paint is peeling or has a weak bond.
  • Moisture is trapped behind the finish.
  • The substrate requires masonry or crack repairs.
  • The existing details cannot accommodate another layer.

Removal exposes the underlying wall, allowing defects to be seen and repaired before the new system is installed. At Pro Rend’s Henfield project, the old render was hacked off before the property was re-rendered with a complete PRB silicone render system.

Can silicone render be applied over pebble dash?

Pebble dash needs the same careful assessment. If it is loose, hollow or extensively patched, applying another system over it may transfer the existing problems into the new finish. Its uneven profile can also affect the preparation and thickness required.

Where pebble dash is retained, the installer must confirm that the background is strong enough and specify a compatible levelling and reinforced render build-up. Where its condition is uncertain or repairs are needed behind it, removal may provide a more dependable starting point.

What should your quotation explain?

For a house, apartment block or commercial property in Worthing, Brighton or elsewhere in Sussex, a useful rendering quotation should make the proposed preparation clear. Look for an explanation of:

  • Whether the existing render will be retained or removed.
  • How loose areas and cracks will be dealt with.
  • What cleaning and preparation are required.
  • Which primer, basecoat, reinforcing mesh and finish are proposed.
  • How windows, sills, pipes and other details will be handled.
  • Which manufacturer’s system will be used.

This allows you to compare the proposed work properly. Two quotations that both say “silicone rendering” may include very different levels of preparation.

Arrange an assessment with Pro Rend Sussex

If you are considering silicone rendering for a painted, rendered or pebble-dashed property, Pro Rend can inspect the existing surface and explain whether an overlay, repair or full removal is appropriate.

We cover Worthing, Brighton, Hove and surrounding Sussex towns, working on residential and commercial properties. See our rendering services or contact Pro Rend for advice or a quotation.